说明

• Brand:Unbranded Color:Clear 物品状况:全新: A brand-new, unused, unopened, undamaged item (including hand-crafted items). See the seller's ... UPC:does not practice Country/Region of Manufacture:China Epoxy Carbon Fiber Glue Black Base Glue A 150g + B 150g For Car Craft Making DIY Shipping quantity: A 150g + B 150g Instructions to be used of carbon fiber coating primer Compared with some so-called quick-drying primers with low viscosity (quick-drying and brittle, and straightforward to delaminate after exposure to the solar in summer),The carbon fiber coating primer of this product makes use of E51 epoxy resin (A) and an improved excessive bonding and high adhesion curing agent (B). It has the benefits of good toughness, strong adhesion, excessive peel resistance, and not smooth to delaminate after being exposed to the solar in summer. This also is the unique aim of our store to come to a decision this mannequin as the carbon fiber coating base glue. However, some prospects complained that the consistency of the base glue in our shop is simply too excessive (caused through low temperatures in winter), that might trigger inconvenience in use. This article will introduce intimately the best way to larger use carbon fiber-coated base glue. Scope of application: ABS plastic, aluminum alloy, iron, wood, ceramic (unglazed) and other polar materials (i.e. materials with painted surfaces or paintable surfaces) Special Note:First: Surface treatment of original partsUse 320-grit sandpaper to dry-sand the outside of the wood object, completely polish the paint surface, and maintain the outside as tough as possible. Then use a utility knife to attain the surface right into a mesh to increase adhesion as a lot as possible.Second: Preheat to minimize viscosityWhen the temperature is less than 20°C, the viscosity of the base glue (B) will increase. When the temperature is less than 5°C, the viscosity of the base glue (A) may even increase. At this time, it may be preheated to reduce the viscosity. Easy to use in proportion. When the temperature is lower than 5℃, (A, B) would be preheated on the same time. Heating the insulated water for approximately 10 mins will vastly minimize the viscosity and make it easier to use.Third: ProportionThe colour of primer (A) may precipitate if left to face for a long time. Before mixing, you might open the bottle cap and stir it with a stirring rod about a times, or change the bottle cap and shake it up and down a few times.According to A:B=1:1 (the volume ratio and weight ratio are the same), take the percentage and mix thoroughly earlier than use.Fourth: PaintingWhen painting, you would roughly observe it first. After brushing, use the recent air setting of a hair dryer or the low setting of a warmth gun to blow the whole surface for 2-3 mins to additional reduce the viscosity and management the thickness of the complete floor to a minimum.1: Use the new air surroundings of the hair dryer, the non-adjustable low setting of the warmth gun, and the adjustable setting of 150-180℃2: Blow the whole surface for 2-3 minutes to extra cut the viscosity3: Press the comb and scrape off the surplus primer to achieve a reasonable thickness (generally the same thickness as standard A4 paper)4: After brushing, place it in the air. After a period of time, the skin could be level.Special reminder: When applying primer, the brush should be pressed right down to allow the primer to completely mix with the unique piece.Fifth: Waiting timeAfter making use of the primer, you should watch for some time to realize the best viscosity when laying the carbon fiber cloth.Please consult with the following for specific occasions 0-10℃ (it is recommended to take heat preservation measures below 0℃)----1.5-2 hours10-15℃----about 1.5 hours15-25℃----1-1.5 hours25-30℃----about 1 hour30-35℃----45-60 minutesBake at fixed temperature 60-65℃ for 15-20 minutesAfter the appropriate time, the stickiness could be superb when touched together with your fingers, and it will seem to be a string, and you may lay the carbon cloth.A note of caution: if the base glue is utilized thickly or if the time is not enough, the carbon cloth could seep out of the surface of the carbon material and impact the effect. Sixth: After laying the carbon cloth, the carbon cloth must be pressed firmly with the palm of your hand to make the carbon cloth totally match the original part. After pressing the whole surface, you may wrap it with plastic wrap and tighten it (keep it wrapped for 1.5-2 hours). Further let the carbon cloth fit the original part. At this point, the entire technique of using the primer is over.Use the primer in line with the above method. After all is completed, the complete carbon fiber can be nearly integrated with the unique part, which might effectively stop edge warping and separation and delamination.

• 
• 
• 
• 
• 

审核