Descriptions

• Silicone electronic potting glue sealing insulation thermal conduction energy battery pack circuit board water-resistant AB comfortable glueThis glue is a two-component silicone digital potting glue, with sealing, insulation, thermal conductivity, excessive and coffee temperature resistance, color is divided into black, gray, transparent, and white, hardness is split into demanding glue and gentle glue, the integration ratio also is diverse , and extra merchandise with weight specifications would be customized, please seek the advice of us for detailsPlease note: transparent shade demanding glue will heat when set, challenging glue cannot be eliminated after solidification, smooth glue could be stripped,The glue consists of brought on substances, please stir flippantly earlier than use, and then blend the A and B ingredients evenly. If the aggregate is not uniform, it will not cureparameterName: Silicone digital potting AB glueSpecifications: 200g、300gColor: black, white, clear, grayMixing ratio: 1:1/3:1/5:1Operation time: about 30 minutesCuring time: 1-10 hours for initial curing, 24 hours for full curingFeatures: insulation, waterproof, thermal conductivity, confidentiality, anti-corrosion, anti-vibration, flame retardantApplication areas: varied sensor potting, precision electronic module potting, lighting fixture potting, power module potting protection, etc. H598 is a gray, low viscosity two ingredient addition molding silicone sealant that may be cured at room temperature or heated after being mixed in a weight ratio of 1:1. It has the attribute of faster curing at larger temperatures. This product does not produce any by-products or stress throughout the curing process, and will not trigger stress stress on electronic devices; Applied to varied electronic products for sealing and protection, it has functions similar to sealing, waterproofing, insulation, thermal conductivity, flame retardancy, etc. After curing, it can be used in environments ranging from -50 ℃ to 200 ℃.Product Features1. Sealing, insulation, waterproof and moisture-proof, dustproof and anti-corrosion.2. Glue has nice flowability, self leveling, and good permeability.3. Flame retardant grade UL94-V-0, with good flame retardant effect.4. High temperature resistance of two hundred ℃, low temperature of -50 ℃, and nice aging resistance.5. Soft gel after curing, non unfavourable electronic components, detachable, and repairable.6. Mix and solidify according to a weight ratio of 1:1, with uncomplicated operation and can be manually poured or routinely poured by means of machine.7. After mixing, it can be naturally cured or quickly cured by heating (the greater the temperature, the speedier the curing speed).Typical Applications◆ Automotive electronics and modules ◆ LED power pressure module ◆ Solar module junction box ◆ Electric vehicle charging column module ◆ Lithium battery pack, capacitor financial institution ◆ Magnetic induction coil ◆ Inverter energy supplytechnical parameterBefore curingAppearance and morphologyComponent A: Grey liquidComponent B: White liquidViscosity (cps. 25 ℃): Component A: 3500-4500Component B: 3500-4500Mixing ratio A component: B component=100:100 (weight ratio)Room temperature usage time (25 ℃): 30-50minForming time (h)30 ℃ Forming time: 1-3h25 ℃ Forming time: 3-5 hoursForming time at 20 ℃: 5-10 hoursCuring time (25 ℃): 24 hours (25 ℃ -30 minutes)After curingAppearance: Gray elastomerHardness (Shore A): 55-65Thermal conductivity coefficient (W/m.K): 1.0Elongation at destroy (%): 200-350Volume resistivity (Ω · cm): ≥ 1.0 × 10[14]Breakdown voltage (kV/mm): 18-25Dielectric loss attitude tangent (1MHz): ≤ four × 10[-3]Dielectric constant (1.0MHz): 2.6-3.1Operating temperature differ (℃): -50~200*The above information information is for reference only, and the categorical dimension via the user shall prevail! Not used as a foundation and standard for acceptance!Usage Guidelines1. Before mixing: First, place ingredient A and factor B in their respective bins and stir thoroughly.2. When mixing: The weight ratio of A aspect to B factor needs to be followed at 1:1, and the mixture should be stirred evenly.3. Bubble removal: After mixing the rubber material, it will be vacuumed for 1-3 minutes.4. Sealing: The mixed adhesive must be poured into the poured product as soon as possible to avoid thickening and poor fluidity of the adhesive in the later stage.5. Curing: Cure at room temperature for twenty-four hours, or at increased temperature. The larger the temperature, the speedier the curing speed.matters needing attention1. The adhesive needs to be saved in a sealed and dry room temperature environment, and the mixed adhesive should be used up as quickly as probable to avoid waste.2. This product is not a hazardous material, yet don't input or eye contact.3. This product is non-toxic, has good physiological inertness, and has no irritation or damage to the skin.4. The product doesn't contain flammable and explosive components, and won't trigger fireplace or explosion accidents. There aren't any special requirements for transportation.5. After storage for a era of time, the adhesive could be layered; Please blend well before use, with out affecting performance.6. The following elements might hinder the solidification or non solidification of this product. Simple experiments can be carried out earlier than use, and if necessary, the appliance discipline ought to be cleaned. (1) Incomplete curing condensed silicone adhesive. (2) Amine cured epoxy resin. (3) White wax welding or rosin welding points. (4) For extra safety precautions for this product, please talk over with the Material Safety Data Sheet (MSDS) of hauaeIf you would like greater specifications of potting glue, please touch us, whatsapp: +86 18705998760, email: lqm112489@163.comHow to use potting glue?1. Before mixing: First, blend A and B elements in various packagings and combine them evenly. (Because the density of the potting glue is very large, throughout garage and transportation, the high particular gravity material will sink to the bottom, causing the end to be thin and the bottom to be thick, which impacts the curing of the glue)2. Mixing ratio: Mix AB substances per the weight ratio.(Because the density of the AB aspect glue is different, the amount ratio is straightforward to trigger the glue not to cure)3. Mixing and stirring: Stir well.Stirring tools: use a round container to stir, don't use irregular shapes, bumpsFor uneven and square containers, disposable paper cups are recommended; the stirring rod should not be too thin, and thicker stirring rods comparable to chopsticks are recommended.Stirring method: All facets of the lowest of the container must be stirred till the colours of the AB substances are combined.4. Deaeration treatment: let the combined and stirred container stand for 5-10 minutes, and the bubbles are naturally dischargedOr use a vacuum defoaming machine to degas at 0.8Mpa for at least 5 minutes.5. Potting: pour the combined glue into the product as soon as possible to circumvent the passage of timeThe viscosity of the colloid increases.6. Curing time: it may be cured naturally below widespread tears: if you want to hurry up the curing speed, you possibly can broaden theAmbient temperature, the better the temperature, the quicker the curing speed!Precautions1. The rubber compound ought to be sealed and stored in a dry room temperature environment. The mixed rubber compound ought to be used up as soon as possible to avoid waste.2. This product is a non-dangerous product, but do not enter it or eye it.3. This product is non-toxic, has nice physiological inertia, and has no irritation and harm to the skin. The product does not contain flammable and explosive ingredients and will not cause fireDisaster and explosion accidents, no special requirements for transportation.4. After a period of storage, the glue can be layered. Please stir effectively before use, it's going to no longer impact the performance.5. The following ingredients could hinder the curing of this product, or the phenomenon of non-curing occurs. Therefore, you must apply it after uncomplicated experimental verification.The application subject needs to be wiped clean if necessary.a. Incompletely cured condensed silicone adhesive. b. Amine curing epoxy resin. c. White wax welding or rosin

• 
• 
• 
• 
• 

Révision