Preces apraksts

• Brand:Unbranded Color:Clear A brand-new, unused, unopened, undamaged merchandise (including home made items). See the seller's ... UPC:does now not apply Country/Region of Manufacture:China Epoxy Carbon Fiber Glue Black Base Glue A 150g + B 150g For Car Craft Making DIY Shipping quantity: A 150g + B 150g Instructions for use of carbon fiber coating primer Compared with some so-called quick-drying primers with low viscosity (quick-drying and brittle, and straightforward to delaminate after publicity to the sun in summer),The carbon fiber coating primer of this product uses E51 epoxy resin (A) and an improved high bonding and high adhesion curing agent (B). It has some great benefits of good toughness, stable adhesion, high peel resistance, and never clean to delaminate after being exposed to the sun in summer. This also is the unique purpose of our shop to make your mind up this model because the carbon fiber coating base glue. However, some clients complained that the consistency of the bottom glue in our shop is too excessive (caused via low temperatures in winter), that might trigger inconvenience in use. This article will introduce intimately learn how to larger use carbon fiber-coated base glue. Scope of application: ABS plastic, aluminum alloy, iron, wood, ceramic (unglazed) and different polar materials (i.e. supplies with painted surfaces or paintable surfaces) Special Note:First: Surface medicine of customary partsUse 320-grit sandpaper to dry-sand the surface of the wooden object, permanently polish the paint surface, and preserve the skin as tough as possible. Then use a application knife to attain the skin into a mesh to extend adhesion as much as possible.Second: Preheat to reduce viscosityWhen the temperature is lower than 20°C, the viscosity of the bottom glue (B) will increase. When the temperature is lower than 5°C, the viscosity of the base glue (A) may even increase. At this time, it may be preheated to minimize the viscosity. Easy to apply in proportion. When the temperature is lower than 5℃, (A, B) could be preheated at the same time. Heating the insulated water for approximately 10 mins will significantly cut the viscosity and make it easier to use.Third: ProportionThe colour of primer (A) may well precipitate if left to face for a protracted time. Before mixing, you could open the bottle cap and stir it with a stirring rod about a times, or replace the bottle cap and shake it up and down about a times.According to A:B=1:1 (the volume ratio and weight ratio are the same), take the share and mix very well earlier than use.Fourth: PaintingWhen painting, you possibly can roughly apply it first. After brushing, use the new air setting of a hair dryer or the low setting of a heat gun to blow the entire floor for 2-3 mins to additional lower the viscosity and management the thickness of the whole floor to a minimum.1: Use the hot air surroundings of the hair dryer, the non-adjustable low atmosphere of the heat gun, and the adjustable setting of 150-180℃2: Blow the whole floor for 2-3 minutes to additional minimize the viscosity3: Press the comb and scrape off the surplus primer to achieve a average thickness (generally the same thickness as normal A4 paper)4: After brushing, place it within the air. After a period of time, the surface will be level.Special reminder: When making use of primer, the comb must be pressed down to enable the primer to totally blend with the unique piece.Fifth: Waiting timeAfter applying the primer, you need to wait for some time to attain the best viscosity when laying the carbon fiber cloth.Please talk to the ensuing for specific times 0-10℃ (it is recommended to take heat preservation measures below 0℃)----1.5-2 hours10-15℃----about 1.5 hours15-25℃----1-1.5 hours25-30℃----about 1 hour30-35℃----45-60 minutesBake at fixed temperature 60-65℃ for 15-20 minutesAfter the appropriate time, the stickiness could be superb when touched along with your fingers, and it will seem like a string, and you'll lay the carbon cloth.A observe of caution: if the bottom glue is utilized thickly or if the time is not enough, the carbon material may well seep out of the surface of the carbon material and affect the effect. Sixth: After laying the carbon cloth, the carbon material must be pressed firmly with the palm of your hand to make the carbon fabric fully match the unique part. After urgent the entire surface, you might wrap it with plastic wrap and tighten it (keep it wrapped for 1.5-2 hours). Further let the carbon material fit the original part. At this point, the whole process of utilizing the primer is over.Use the primer per the above method. After all is completed, the whole carbon fiber will be almost included with the unique part, which can efficiently forestall edge warping and separation and delamination.

• 
• 
• 
• 
• 

Atsauksmes