Description

• Brand:Unbranded Color:Clear 物品状况:全新: A brand-new, unused, unopened, undamaged item (including handmade items). See the seller's ... UPC:does now not practice Country/Region of Manufacture:China Epoxy Carbon Fiber Glue Transparent Glue A 200g +B 100g For Car Craft Making DIY Shipping quantity: A 200g + B 100g Instructions for use of carbon fiber protecting tapeFirst: before matchingWhen the temperature is less than 15°C, (A) the viscosity will increase. This is a characteristic of epoxy resin and is a standard phenomenon. (A) can be preheated earlier than mixing to reduce the viscosity and facilitate use. (Can be heated with water) Tighten the bottle cap and warmth with water for approximately 10 mins earlier than taking it out.After taking it out, use a paper towel or dry cloth to dry the water on the bottle to prevent water from blending in throughout blending and affecting the effect.Second: ProportionCarbon fiber masking tape ought to be strictly and precisely proportionedThe percentage is:Weight ratio (electronic scale ratio) A:B=2:1 Step 1: Take (A) 18 ml, (B) 10 ml (you can blend the ratio consistent with your personal situation)After taking the measured amount, pour it right into a disposable cup and mix thoroughly. Remember to scrape the inside of the measuring cup clear to circumvent errors that will end in incomplete curing.When the temperature is increased than 25°C, stir thoroughly and let it sit down for 3-5 minutes. It can be used after maximum of the bubbles have dissipated.When the temperature is 15-25°C, you need to use a hair dryer or hot air gun (low setting if there is not any temperature display, and 150-180°C if there's a temperature display) after blending the combination evenly, blow it for 20-30 seconds, after which let it take a seat for 1-2 seconds. Use after minutes.When the temperature is less than 15°C, it is best to preheat (A) earlier than proportioning. After stirring evenly, you would let it sit for 2-3 minutes or use a hair dryer with a scorching air environment or a heat gun (use a low setting if there isn't any temperature display, or a surroundings with a temperature display). 150-180℃), blow for approximately 20 seconds and use directly.Third: PaintGenerally speaking, it only takes 4-5 instances to sweep a natural flat board, and 5-6 times to brush a curved board.Before applying the skin glue, ensure you totally saturate the brush and press to expel air bubbles in the brush.When painting, you should press the brush slightly harder to minimize the thickness of the paint. The mask should be used within 20 mins at 25-35°C, and it should be used inside quarter-hour after preheating or blowing with a sizzling air gun and hair dryer. If you are working on a enormous piece or a relatively huge piece, you would possibly no longer have satisfactory time to color it over and over again. You can first pour it over for multiple items or extensive pieces, after which paint it carefully. This can efficiently keep away from the problem of too much mixing and too past due to brush.Fourth: Curing time and portray interval0-10℃ (it is recommended to take heat preservation measures below 0℃)----10-12 hours10-15℃----7-8 hours15-25℃----6-7 hours25-30℃----5-6 hours30-35℃----4.5-5 hoursBake at fixed temperature 60-65℃ for roughly 25-30 mins to treatment In order to save lots of time and procure higher results, the following is the optimum production time (taking 25°C as an example)This system is acceptable for normal DIY companions who do not have a relentless temperature oven or chopping and grinding tools.Apply the 1st coat of masking tape↓(After about 6 hours of curing)After cutting off the excess carbon cloth, lightly rub the whole floor with 240-grit sandpaper.Brush the second time↓(Wait for approximately 1-1.5 hours, until it is semi-dry and there's no fluidity at the surface)Refresh the 1/3 time↓(Wait for about 1-1.5 hours, until it's semi-dry and there is no fluidity on the surface)Brush the fourth time↓(Wait about 6 hours for curing)Slightly sand the entire floor with 240-grit sandpaper (dry sand) and brush it calmly for the 5th time.↓(Wait for roughly 1-1.5 hours, until it's semi-dry and there isn't any fluidity on the surface)Brush the sixth time (usually the last time)↓(After curing for roughly 6 hours, beginning water sanding from coarse to superb sandpaper)After the final cross of surface glue is cured, and water is added to the sandpaper from coarse to fine, the outside can be permanently freed from trachoma and pits. Fifth: Things to noteIt is also most important to explain1. The carbon fiber coating glue is fabricated from epoxy resin and wishes to be accurately mixed and mixed very well before use.Do no longer visually examine the ratio. If the ratio error exceeds 5%, it's going to end in incomplete curing (not curing for an extended time, or will probably be too soft).2. When the facial glue is in liquid state or before it is permanently cured, please put on water-resistant gloves to circumvent direct touch with the surface or areas that do not need to be in contact (such as clothing, etc.).After contact, it may be cleaned with medical alcohol, liquor, gasoline or organic solvents.3. Try to avoid working in environments with humidity exceeding 90%.4. Try to bypass contact with hot temperature (temperature exceeding 100°C) environment for completed products.

• 
• 
• 
• 
• 

Review